ISO 16047 PDF

according to test requirements such as BS Pt. 2 or ISO This can be expressed in two ways, the Coefficient of Friction µ and the Torque Coefficient (K . ISO FASTENERS – TORQUE/CLAMP FORCE TESTING. DIN EN ISO Fasteners – Torque/clamp force testing (ISO + Amd ) (includes Amendment).

Author: Voodoolmaran Vocage
Country: Nicaragua
Language: English (Spanish)
Genre: Health and Food
Published (Last): 23 October 2004
Pages: 180
PDF File Size: 12.56 Mb
ePub File Size: 8.33 Mb
ISBN: 541-4-47121-898-8
Downloads: 35621
Price: Free* [*Free Regsitration Required]
Uploader: Grozil

The ISO standard describes reproducible laboratory tests. The respective complementary partial torque can be identified via subtraction.

BS EN ISO 16047:2005+A1:2012

Username or email address: Have fun clicking through! In cases where fluid flow is critical either gas or liquid CFD can be used to optimize flow and minimize turbulence, sio to predict how two different liquids are mixing, etc.

sio Coefficients of friction cannot be specified using measurement technology. Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work. Start Webshop Product catalog Product presentation.

Some of the capabilities at Matrix Engineering Consultants iwo If the factor is very high, fasteners need to be tightened with a high torque and the efficiency of the fasteners decreases. The variety around the topic of corrosion and corrosion protection is also in our glossary at home: Need more than one copy?

Based on this data, the nut factor or total coefficient of friction can be calculated and used to evaluate the effect of various fastener finishes, coatings, lubricants and manufacturing processes. With izo fasteners a washer is threaded onto the blank; the subsequent cold forming in which the thread is rolled into the surface ensures that this washer cannot fall off. By repeating the test on a sample of the fasteners, the variation in the torque-tension relationship, can be established for an application.

  FIRE WITHIN DUBAY PDF

Already Subscribed to this document. When tightening the uso the clamp force, the rotation angle, the total torque and one of the two partial torques are measured.

ISO – Fasteners — Torque/clamp force testing

The friction between roughened surfaces is greater than between smooth ones. As a result, the coefficients of friction calculated from torque and clamp force only really apply to the conditions on the test bench. If you need to be able to add standards to the monitoring service, you must register as a user with your own username and password.

It can also be used in conjunction with FEA when a transfer of fluid causes a resultant force that needs to be considered when doing structural analysis. These are useful, for example in comparing the coefficients of friction of different coating systems. However, specialists also take a closer look. If fasteners are lubricated, friction is reduced — this applies both with regard to both external lubrication via grease or wax and integrated lubrication via the addition of a lubricant to the coating.

FEA can give virtual insight into the structural integrity of new designs before any capital is spent building parts.

Torque to Yield Tests MEC can be lso tests on actual fastened assemblies to obtain torque-angle graphs and to establish the torque to reach the yield strength of the bolt. They are identified via torque and clamp force. There are many types of engineering simulation and analyses that Matrix Engineering Consultants performs either as a stand-alone service or integrated into our projects.

  ABNT NBR 13752 PDF

Simple instrumented fixtures with manual testing and data capture Automated testing of complex systems with customized control dashboards and reports. This technique has a distinct advantage because the actual joint and fastener can be tested without compromising the joint stiffness through the introduction of a load cell. Please enter your username or email address. In this process the fasteners are screwed to their own washer. This standard is not included in any packages.

ISO 16047:2005

This standard is also available to be included in Standards Subscriptions. For example, brighteners in the galvanised coat serve to lower the friction between reference part and fastener. We have no document history for this lso. In practice, tightening instructions often specify fitting fasteners with a specific torque. Your Alert Profile lists the documents that will be monitored.

The option of choosing between uncoated and galvanised bases reflects the prevailing procedures in the American and European areas. MEC can be perform tests on actual fastened assemblies to obtain torque-angle graphs and to establish the torque to reach the yield strength of the bolt. You may io a document from your Alert Profile at any time.

When fastening, the torque must be correct in order to achieve the required clamp force — the force that a fastener uses to hold two components together.

With these tests it is also possible to check the quality of the coating in ongoing production. If the document is revised or amended, you will be notified by iiso.